Acer Altos G901 User Manual Page 118
- Page / 244
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3 Hardware configuration
102
7
8 Remove the two plastic rivets and the plastic overlay from the
power distribution board.
9 Attach the plastic overlay to the new power distribution board
using the two plastic rivets.
10 Grasp the new power distribution board and overlay with the
power supply connectors facing the power supply bays.
11 Tilt the edge of the power distribution board in your hand about
30° and gently slide the other edge of the board into the four slots
in the power supply bays.
12 When the board is inserted all the way into the slots, tilt the board
down so the four mounting holes on the edge of the board are
aligned with the corresponding holes in the main chassis.
13 Tighten the four screws to secure the power distribution board to
the main chassis.
14 Install the power supplies.
15 Install the electronics bay (refer to page 49).
16 Connect the cables to the power distribution board and
mainboard.
17 Close the front subchassis and electronics bay.
18 Install the front and rear access covers (refer to page 46 and
page 45).
Label Description Label Description
A Power supply module B Screws
BB!H:11!vh!.!FO/cppl!!Qbhf!213!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN
- Acer Altos G900 1
- FCC notice 3
- Laser compliance statement 4
- Important safety information 5
- Precautionary reminders 6
- Important safety instructions 8
- Contents 11
- 3 Hardware configuration 39 12
- 4 BIOS setup 109 13
- Index 227 15
- 1 System tour 17
- Features overview 19
- Access covers 21
- Main chassis components 22
- Electronics bay components 23
- Front control panel 24
- Rear panel 26
- Peripheral device bay 28
- Server board set features 29
- Mainboard jumpers 31
- Boot block jumpers 32
- Main jumpers 33
- Serial port B jumpers 34
- System cables 35
- Figure 11 36
- System features 38
- Onboard video 39
- Network interface controllers 39
- Hot-swap hard drive bays 40
- Power supply 41
- System fan 41
- 1 System tour 42
- 2 System setup 43
- Getting started 45
- Checking the package contents 46
- Setting up your system 48
- Hardware setup 49
- Self Test (POST) 50
- Hot keys for POST 51
- Software setup 52
- Network teaming features 53
- Adapter Fault Tolerance 54
- Adaptive Load Balancing 54
- 3 Hardware 55
- Installation precautions 57
- Preinstallation instructions 58
- System access panels 60
- Front access panel 61
- Front subchassis and rear 63
- To remove the electronics bay 65
- Accessing the system boards 67
- Memory board 68
- To install the memory board 69
- Processor board 70
- Mainboard 71
- To install the mainboard 74
- DIMM sequence 76
- To remove DIMMs 77
- Figure 26 - Removing a DIMM 78
- Processors 79
- To install processors 80
- To remove processors 81
- PCI add-in boards 83
- Power LED state Status 84
- Green Power to slot 84
- Amber Fault on slot 84
- Not lit No power to slot 84
- Hot-swap SCSI drives 91
- A Air Baffle C Plastic rail 93
- B Screw D Plastic rail 93
- C Locking slot 95
- DC power supplies 97
- 3 Hardware configuration 100
- Cooling system fans 101
- To remove a fan module 102
- To install a fan module 102
- Backup battery 103
- Front panel board 105
- Diskette drive 107
- 5.25-inch peripheral drives 110
- Label Description 111
- A Data cable 111
- BPower cable 111
- C Slide rails 111
- Hot-swap drive bays 114
- Power distribution board 117
- Fan distribution board 119
- Foam fan baffle 121
- Hot-plug indicator board 123
- B Rivet sleeve 124
- 4 BIOS setup 125
- BIOS parameters 126
- BIOS setup 127
- Using BIOS setup 128
- Primary IDE Master/Slave 132
- Processor Settings 134
- Advanced 135
- Memory Configuration 137
- PCI Configuration 138
- Hot-plug PCI Control 139
- Empty Bus Default Speed 140
- Embedded SCSI 141
- Embedded NIC 1 (10/100) 142
- Embedded NIC 2 (Gbit) 143
- Embedded Voice Controller 144
- I/O Device Configuration 145
- Advanced Chipset Control 147
- Security 148
- To set a security password 150
- System Management 154
- Console Redirection 155
- 4 BIOS setup 156
- Appendix A: System rack 159
- System rack installation 161
- Tools and supplies needed 162
- Equipment rack precautions 162
- Precautions 163
- Rack conversion procedures 164
- Removing the left panel 165
- Removing the feet 167
- Installing the rack bezel 168
- Appendix B: System 175
- Software and utilities 177
- Integrated hardware system 178
- System event log 179
- Platform event management 180
- Emergency management port 181
- System Setup Utility 182
- Running the SSU 183
- Working with the GUI 184
- Customizing the SSU interface 184
- Setting boot device priority 185
- Setting the admin password 186
- Setting the user password 186
- Viewing the system event log 187
- Viewing FRU information 188
- Viewing Sensor Data Records 189
- To verify the firmware 190
- Alerting for platform events 191
- To set up paging alerts 192
- To set up LAN alerts 194
- Managing the server remotely 195
- Exiting the SSU 198
- FRU/SDR load utility 199
- Command line format 200
- Displaying a given area 200
- Using a specified CFG file 201
- Using a specified FRU file 201
- SCSISelect 202
- Software updates 203
- Software update packages 204
- Individual updates 205
- Firmware updates 206
- FRU/SDR updates 207
- Equipment log 211
- Calculating power consumption 212
- +3.3 V +5 V 213
- +12 V -12 V 213
- Troubleshooting 215
- Appendix D: Troubleshooting 218
- Monitoring POST 219
- Appendix E: Codes and error 227
- Standard BIOS post codes 229
- Recovery BIOS POST codes 235
- BMC beep codes 237
- POST error messages and codes 238
© 2020, manymanuals.com. All rights reserved. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals