Acer S211HL User Manual

User GuideAcer LCD Monitor

xFederal Communications Commission Declaration of Conformity Name of Responsible Party: Acer America Corporation Address of Responsible Party: Contac

Information for your safety and comfort iiiSafety instructions iiiiiiCleaning your monitor iiiConnecting/disconnecting the device iiiAccessibility ivS

Troubleshooting 14VGA mode 1415DVI/HDMI mode

1EnglishUnpackingPlease check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or

2EnglishAttaching the base (for selected models)Note: Remove the monitor and monitor base from its packaging.Carefully place the monitor face-down on

3EnglishScreen position adjustmentTo optimize the viewing position, you can adjust the monitor tilt, using both of your hands to hold the edges of the

4EnglishDisplay Data Channel (DDC)To make installation easier, so long as your system supports the DDC protocol, the monitor is able to plug-and-play.

5EnglishPIN No. Description PIN No. Description1 TMDS Data2+ 2 TMDS Data2 Shield3 TMDS Data2– 4 TMDS Data1+5 TMDS Data1 Shield 6 TMDS Data1–7 TMDS Dat

6EnglishStandard timing table1640x48060 Hz2640x48072 Hz3640x48075 Hz4MAC640x48066.7 Hz5VESA720x40070 Hz6800x60056 Hz7800x60060 Hz8800x60072 Hz9800x600

7EnglishInstallationTo install the monitor on your host system, please follow the steps below:Steps1 Connect the video cablea Make sure both the monit

Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such cha

8EnglishUsers controlsBase controlsIcon Item DescriptionPower button/indicatorTurns the monitor on/off. indicates power on. Amber indicates standby/

9EnglishAcer eColor ManagementOperation instructions1 Press the Empowering Key to open the Acer eColor Management OSD and access the scenario modes.

10Adjusting the OSD settingsNote: The following content is for general reference only. Actual product specifications may vary.Press the Menu key to op

11Adjusting the OSD position1 Press the Menu key to bring up the OSD.2 Using the directional keys, select OSD from the onscreen display. Then naviga

12Adjusting the setting1 Press the Menu key to bring up the OSD.2 Using the keys, select Setting from the OSD. Then navigate to the feature

13Product information1 Press the Menu key to bring up the OSD.2 Using the keys, select Information from the OSD. Then the basic /information

14Troubleshootingtroubleshooting list below to see if you can self-diagnose the problem.VGA modeProblem LED status RemedyNo picture visible Using the

15EnglishProblem LED status RemedyNo picture visible Using the OSD, adjust brightness and contrast to maximum or reset to their default settings.Off C

iiiInformation for your safety and comfortSafety instructionsRead these instructions carefully. Keep this document for future reference. Follow all wa

ivAccessibilityBe sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possi

vampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total ratin

viNote: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage an

viiNevertheless, some pixels may occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not constitute

viiiTaking care of your visionLong viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens,

ix Acer Incorporated 8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih Taipei Hsien 221, Taiwan Tel : 886-2-2696-1234 Fax : 886-2-26